Emulated Output = Headphones?

[howdy71]

Hi there,

I am very much interested in the ID:60. Just one question needs to be answered, but here in Germany no one can answer 100% sure!

Can the emulated output on the ID:60 been used for plugging a headphone in, in order to use the amp for practising?!

BTW: Great Forum!!!

[kalseru]

Simple answer is yes.

[howdy71]

Thanks, that helps a lot!

[myk.robinson]

Hey, just answered you on my YouTube post
Was going to come back here, then realized it's the same person.

For anyone else who may have had the same question, here's what I found on mine:

Tried just a few minutes ago. I think it will vary depending on the headphones you use. It sounded fine in my studio monitor headphones, but one thing that was bothersome is the fact that you have no real control over the volume level. You can turn the master volume all the way down, but the emulated out sends line level volume because of what it's meant for. So the only control you have is to reduce the channel volume. Probably should run to a mixer then to headphones It does work, though

[BLACKSTARFAN]

OK,Here Goes,...
IF you have another Amp that HAS A HEADPHONES JACK,ALONG with an FX Loop,TAKE the Emulated Output from your ID Amp,plug it into the EFFECTS RETURN Input on the "HEADPHONE AMP",Now you are just using the POWER AMP Section of your Other amp,and if it's equipped with an automatic Speaker "SILENCER" that kicks in when using the headphone jack,all you need to do is utilize the MASTER VOLUME on the HEADPHONE AMP,and you'll be able to control the Headphone Volume.
IF the ID Amp doesn't have a Speaker Silencer,you may need to disconnect the Speaker Outputs on the BLACKSTAR,Or the Sound will BLARE out of the speakers.
HOPE that made sense to you,but,If you need to Play in the WEEE Hours and NOT WANT to wake the Neighborhood,then Desperate times call for Desperate Measures : )
GO ROCK Da HOUSE!!!

[Billthebiker77]

A little help here. I’m trying to use headphones on my ht club 40 using the emulating jack as instructed. Problem is I only get sound on the left phone.
What am I doing wrong? I’m not using an Id core. Ht club 40. I don’t care about answers for ID Core. Help????!!

[Billthebiker77]

Thanks, that helps a lot!

m

Hey, just answered you on my YouTube post
Was going to come back here, then realized it's the same person.

For anyone else who may have had the same question, here's what I found on mine:

Tried just a few minutes ago. I think it will vary depending on the headphones you use. It sounded fine in my studio monitor headphones, but one thing that was bothersome is the fact that you have no real control over the volume level. You can turn the master volume all the way down, but the emulated out sends line level volume because of what it's meant for. So the only control you have is to reduce the channel volume. Probably should run to a mixer then to headphones It does work, though

[Billthebiker77]

I don’t want answers for other amps. Just the HT Club 40. Of course the ID Series has a headphone jack. What input should I use on the HT Club 40.

[Billthebiker77]

Hey, just answered you on my YouTube post
Was going to come back here, then realized it's the same person.

For anyone else who may have had the same question, here's what I found on mine:

Tried just a few minutes ago. I think it will vary depending on the headphones you use. It sounded fine in my studio monitor headphones, but one thing that was bothersome is the fact that you have no real control over the volume level. You can turn the master volume all the way down, but the emulated out sends line level volume because of what it's meant for. So the only control you have is to reduce the channel volume. Probably should run to a mixer then to headphones It does work, though

[Billthebiker77]

But are you using the HT Club 40?